Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)

Ask More Info Of  A Seminar Ask More Info Of A Project Post Reply  Follow us on Twitter
11-05-2011, 08:09 PM
Post: #1


IV report


Conventional substations requires, small installation size, protection against atmospheric pollution and moisture, noiseless operation, nonexplosive and flame resistant, reduced maintenance, minimal radio interference, but totally enclosed substations using SF6 gas as insulation that are also known as GIS is now in widespread use in the electrical power industry .
A GIS has many advantages over a conventional substation, including a space saving and flexible design, less field construction work resulting in quicker installation time, reduced maintenance, higher reliability and safety, and excellent seismic withstand characteristics. Aesthetics of GIS are far superior to that of a conventional substation, due to its substantially smaller size. A GIS can even be installed in a building, if desired. When all of these advantages are taken into consideration, a GIS is a cost effective alternative to a conventional substation that offers many benefits to the end user.

• Bus bars
• Circuit breakers
• Disconnecting switches
• Earthing switches
• Current transformers
• Voltage transformers
• Densimeter
• Cable and boxes
• Gas supply and gas monitoring equipment
• Local control

Under short circuit conditions, the current in a circuit may reach tens of thousands of amperes at a power factor as low as 0.1. A circuit breaker is used to interrupt such currents as soon as possible to avoid equipment damage. High-voltage circuit-breakers have greatly changed since they were first introduced about 40 years ago, and several interrupting principles have been developed that have contributed successively to a large reduction of the operating energy. These breakers are available for indoor or outdoor applications, the latter being in the form of breaker poles housed in ceramic insulators mounted on a structure.
Current interruption in a high-voltage circuit-breaker is obtained by separating two contacts in a medium, such as SF6, having excellent dielectric and arc quenching properties. After contact separation, current is carried through an arc and is interrupted when this arc is cooled by a gas blast of sufficient intensity.
Gas blast applied on the arc must be able to cool it rapidly so that gas temperature between the contacts is reduced from 20,000 K to less than 2000 K in a few hundred microseconds, so that it is able to withstand the transient recovery voltage that is applied across the contacts after current interruption. Sulphur hexafluoride is generally used in present high-voltage circuit-breakers (of rated voltage higher than 52 kV).

Disconnectors or isolators are used for electrical isolation of circuit parts. They are slow acting and operating at off load. Disconnectors must be carefully designed and tested to be able to break small charging current without generating too-high over voltage.

LCC is the interface cubicles to all secondary systems of a substation which are represent a station control and protection. It includes control and alarm functions as well as the correct distribution of auxiliary power supply for the relevant GIS bay.

Slow-operating earthing switch are used for protection purpose when work is being done in the substation, but are operated only when it is certain that the high-voltage system is not energized. The fast-closing earthing switch can close against full voltage and short circuit power. The high speed earthing switch is achieved by means of a spring-closing device.

The potential transformers are employed to step down the voltage and feed the potential coils of indicating and metering instruments and relays. It is identified by single incoming connection and a grounded outgoing connection.

Current transformers are used to feed the current coils of indicating, metering instruments and protective relays. They are identified by the series connection. Normally they have a turns ratio of 1:2000. Tapings are taken in order to change the turns ratio as per requirement
The primary and secondary turns are immersed in SF6, which can be placed above or below the insulator. The advantage of providing the tank above the insulator over providing it below is the saving of copper. When the current in the primary exceeds the rated current, the relay coil is energized and this trips the circuit breaker. In order to avoid flashing, the secondary of the CT should never be left open and should be shorted.
• SF6 does not harm to the ozone layer.
• Sf6 gas is chemically stable.
• Non poisonous & non inflammable.
• Colourless & heavier than air.
• Almost water insoluble.

.docx  GAS INSULATED SWITCHGEAR SUBSTATION.docx (Size: 15.9 KB / Downloads: 217)
Share GAS INSULATED SWITCHGEAR SUBSTATION To Your Friends :- Seminar Topics Bookmark
Post Reply 

Marked Categories : switch gear seminar topics, gas insulated substation over convntional substation pdf, gas insulated substation trivandrum, gas insulated substation installation and maintenance, how to prepare a report on industrial visit on substation, gas insulated switchgear for substations, how to prepare a report on industrial visit on electrical substation, seminar on gas insulated switchgear, gas insulated switchgear substation, gas insulated sub station trivandrum, gas insulated substation queries, gas insulated substation, gas insulated switchgear substation ppt, gas insulated switchgear, seminar topic on switchgear, presentation on gas insulated substations pdf,

Quick Reply
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  technical visit to Loreto substation computer science crazy 0 0 05-09-2016 05:56 PM
Last Post: computer science crazy
  Industrial Training at NTPC Anta Gas power Plant full report seminar topics 12 35,407 31-08-2014 02:50 PM
Last Post: Guest
  132 KV SUBSTATION IFFCO UNIT AONLA, BARIELLY project girl 0 709 02-02-2013 02:37 PM
Last Post: project girl
  33 KV SUBSTATION, DCW BCCL, JHARKHAND project girl 0 609 02-02-2013 02:25 PM
Last Post: project girl
  INDRAPRASTHA GAS LIMITED seminar tips 0 364 11-01-2013 03:22 PM
Last Post: seminar tips
  Asahi Switchgear Products Ltd PPT project girl 0 544 01-12-2012 06:36 PM
Last Post: project girl
  Sourcing of Gas by Indian Companies seminar tips 0 379 17-11-2012 05:38 PM
Last Post: seminar tips
  Uttar Pradesh power corporation Limited 400/220/132kv substation Sultanpur seminar flower 0 1,544 20-10-2012 02:13 PM
Last Post: seminar flower
  OIL & NATURAL GAS CORPORATION LTD., ANKLESHWAR ASSET seminar flower 0 2,254 21-09-2012 12:04 PM
Last Post: seminar flower
  GAS-FIRED COMBINED-CYCLE POWER PLANTS ppt seminar flower 0 1,530 19-09-2012 01:35 PM
Last Post: seminar flower
This Page May Contain What is GAS INSULATED SWITCHGEAR SUBSTATION And Latest Information/News About GAS INSULATED SWITCHGEAR SUBSTATION,If Not ...Use Search to get more info about GAS INSULATED SWITCHGEAR SUBSTATION Or Ask Here